The PLS3 laser tool by Pacific Laser Systems is a self-leveling, accurate and durable point-to-point layout tool for the professional contractor. PLS3 features a 3-beam laser that gives reference points for plumb and level layout. Small and durable, the PLS3 has an accuracy of 1/4 inch at 100 feet and is self-leveling. With PLS3, you can lay out reference points faster than traditional, labor-intensive methods and you don't require any swinging plumb bobs to get your job done. You can plumb instantly from floor to ceiling of from 50 feet off the ground which allows you to take clear, stable reference points both indoors and outdoors.
The unique PLS3 cantilever design allows for easy sight of the opposing reference points. The PLS3 is designed with advanced dampening, which means that vibrations that occur on the jobsite will not cause the reference points to easily bounce around. This is especially important when the contractor is moving the PLS3 tool quickly along the channel, checking for plumb.
PLS3 Self-Leveling Laser Tool Features:
- Self-Leveling: Instant and continuous leveling
- 3 Laser Beams: Forward, Up and Down (Level and Plumb)
- Range: +/- 100 feet (+/- 30.5m)
- LED Indicator: On/Off, Tilt, Battery Low
- Accuracy (All Beams): <1/4" at 100 feet, Cantilever Design: Allows for easy sight of opposing reference points
- Tripod Mount: 1/4 x 20 threaded mount in base
- Floor Stand: Included floor stand allows for placement on flat surfaces
- Defective item will replace or repair, no refund
- Magnetic Wall Bracket: Includes magnetic wall mounting bracket
- Battery Operated: 3 AA batteries (not included). Battery Life: +30 hours continuous use
PLS3 Self-Leveling Laser Includes:
- PLS3 Laser Unit
- Operating Manual
- Wall Bracket
- Carrying Pouch
- Floor Stand
- 1 Year Warranty
PLS 3 Self-Leveling Laser Tool Applications:
Using PLS3 for Glazing Construction (Flat Glass Industry):
Safety and accuracy are paramount for the glazing contractor. Often facing windy conditions coupled with heights and heavy materials, the glazier needs fast point-to-point layout of his project. Swinging a plumb bob in the wind is time consuming and expensive. Glaziers use PLS3 laser tool to accurately plumb and level channel and mullions in the most adverse building conditions. Once the bottom channel is down and fastened, the glazier must attach the top channel plumb to the bottom channel. The PLS laser can be placed perpendicular to the channel with the plumb (down) beam on the outside bottom edge of the channel. The point on the ceiling is where the top track must be fastened.
Using PLS3 for HVAC Construction Installation:
The PLS3 coupled with the optional magnetic wall bracket is a proven solution that HVAC contractors have come to depend on when performing installation of ductwork. The contractor can lay out the design on the slab or sub floor and then attach the PLS3 magnetically to the side of the lift. This allows the contractor to remain working on installation on the ceiling while shifting the lift over each point on the floor. This provides time savings and safety benefits that are realized instantaneously. Because the accuracy of the PLS3 laser tool is the same on each beam, the contractor could be on a large commercial project, high in the air, assured that he is transferring plumb points at significant distance. The portability of the PLS3 laser tool allows the HVAC contractor to level the HVAC system they are installing by placing the PLS3 laser tool on virtually any surface.
Using PLS3 for Steel Stud Framing:
Before a framing contractor can construct walls, he or she must lay out the job, snap the control lines and fasten the track. A contractor must perform a 3-4-5 or 6-8-10 (Pythagoras) to ensure that walls intersect at perfect 90º angles. This is a two-person task but materials and job boxes can get in the way of pulling tape, compromising the accuracy of the payout. Laying our control lines with the PLS3 system is a fast and accurate task. Once the bottom track is down and fastened, the contractor must attach the top track plumb to the bottom track. The PLS3 laser can be placed perpendicularly to the track with the plumb (down) beam on the outside bottom edge of the track. The point on the ceiling is where the top track must be fastened.